CH341A 编程器使用说明v1.5

liyf 发表于 2019-11-16 11:45:50

CH341A 编程器使用说明
(彩灯版v1.5)2019.11.15
目录
一、CH341A编程器简介..................................................................................................................3
二、编程器硬件部分.......................................................................................................................4
1、输出电压Vout....................................................................................................................4
a）1.8v拨动开关位置参考.............................................................................................6
b）2.5v拨动开关位置参考.............................................................................................6
c）3.3v拨动开关位置参考（默认）.............................................................................6
d）5v拨动开关位置参考................................................................................................6
2、spi输出..............................................................................................................................8
3、TTL输出............................................................................................................................9
4、TTL自检..............................................................................................................................9
5、红外测码...........................................................................................................................11
6、彩灯说明...........................................................................................................................13
7、芯片放置...........................................................................................................................14
8、通用转接板.......................................................................................................................15
9、93xx芯片的放置方式图..................................................................................................16
10、45xx芯片的放置方式....................................................................................................17
11、st95xxx系列汽车存储芯片...........................................................................................18
12、KB901x类芯片接线图..................................................................................................19
13、qfn8转接板....................................................................................................................20
14、bga24转接板..................................................................................................................21
15、bga24 8mm*6mm 4*6球阵列翻盖座.........................................................................22
16、bga24 8mm*6mm 5*5球阵列翻盖座.........................................................................24
17、qfn8 8mm*6mm 翻盖座................................................................................................25
18、qfn8 6mm*5mm 翻盖座................................................................................................26
三、安装驱动.................................................................................................................................27
1、编程器驱动.......................................................................................................................27
2、TTL串口驱动..................................................................................................................27
四、编程器软件.............................................................................................................................28
1、AsProgrammer ..................................................................................................................28
2、ch341 usb编程器软件.....................................................................................................29
五、常见问题及处理方法.............................................................................................................30
1、土豪金版的软件读写32M芯片不正常.........................................................................30
2、AsProgrammer不能读写microchip的93LC46A，93LC66A ......................................30
3、正在读写操作时，操作软件会出现读写状态灯灭掉...................................................30
4、AsProgrammer读出文件比艾科等专业编程器的小......................................................30
5、AsProgrammer读写w25q64fw不正常..........................................................................30
6、win10系统下AsProgrammer读写可能不正常.............................................................30
7、同样芯片型号怎么比你的读写慢...................................................................................30
8、编程器插上电脑有时能识别有时又不能.......................................................................30
9、电压开关已经拔到5V，但是电压只有4.2v.................................................................30
10、USB-TTL检测老是失败...............................................................................................30
11、USB-TTL检测提示不能打开端口错误........................................................................31
12、自动编程总是校验地址00000000错误.......................................................................31
13、红外测码有时能测有时不能.........................................................................................31

liyf 发表于 2019-11-20 08:38:18

14、点自动编程器后在去保护环节卡住不走
芯片放置错误位置或者芯片接触不良，点停止按钮，退出编程状态。重新放置好芯片后，点问号按钮，确认芯片是否能读出id，能读出了说明接触没问题。

yu68805205 发表于 2019-11-21 02:44:47

先赚一点银两在下载吧好难啊!

yu68805205 发表于 2019-11-21 02:45:20

先赚一点银两在下载吧好难啊什么情况？

天天向上 发表于 2019-11-21 17:48:10

努力回帖！赚银两，赚积分

阿财_R19XH 发表于 2019-11-25 19:35:51

不错，好好学习学习

a_tao9999 发表于 2019-12-3 22:06:47

好好学习学习

weln2020 发表于 2020-1-14 01:30:46

做产品不易支持版主;P

apexmicaa 发表于 2020-1-21 17:44:51

谢谢楼主分享，支持一下@

nmcfzxd 发表于 2020-2-17 09:01:54

谢谢楼主分享，支持一下

页: [1] 2 3 4 5