行业的代表-MG3641A 合成信号发生器

admin

MG3641A 合成信号发生器
	最近更新日期：2006-10-03
	厂商名称：                         Anritsu                          商品名称： 合成信号发生器 商品型号： MG3641A 简单信息：

特点
    125千赫至1040/2080兆赫：经济而高性能的信号源新的Anritsu合成器技术允许在整个频率量程范围内把频率设置在0.01赫兹的分辨率上。在任何频率上可靠测量所产生的一种独特的低噪音钇铁石榴石（YIG）振荡器产生单边带相噪音好于-130分贝/赫兹（1千兆赫，20千赫偏差）的高纯度信号，使这些信号发生器可用于无线电接收机的干涉测试和不同的本地信号源和参照信号 。
性能：
·0.01赫兹，0.01分贝的分辨率
·高信号纯度（-100dBc乱真信号）
·多样化的调节功能
技术指标

Carrier frequency	Range:125kHz to 1040MHz             Resolution:0.01Hz             Accuracy:Reference oscillator accuracy;reference oscillator accuracy±(0.3%ofFM setting deviatin+5Hz)at frequency modulation             Internal reference oscillator*^1             Frequency:10MHz ,Aging rate:±5*10^-9/day,Start-up characteristics:1*10^-7/10min(for 24 h after power on )             Temperature stability:±3*10^-8(0° to 50℃)             External reference input:5/10 MHz,±10ppm,&ge;0.7Vp-p/50&Omega;(AC coupling) ,BNCconnector(rear panel)             Buffer output:10MHz TTL level(DC coupling )BNC connector(rear panel)             Switching timw:<40ms (external control mresponse time fron lase commanduntil becomes within±0.01ppm of set frequency)
Output	Range:-143 to +17dBm (settable range:-143 to +23dBm)             Units:dBm,dB&mu;,V,mV,&mu;V,(dB&mu;,V,mV and &mu;V switchablebetween terminationvoltage display and open voltage display)             Resolution:0.01dB             Frequency characteristics(at 0dBm):±1.0dB(pulse modulation:on(*^2             Impedance:50&Omega;(N connector )VSWR :<1.5(&le;-3dBm),<2.5(>-3dBm)             Switching time :<50ms(normal mode)<100ms (level safetymod)<10 ms(continuous mode)             *Response time from last command until becomes within±0.5dB of final level             Special setting mode             Continuous mode:Variable within set value±10dB with no interruption of output             Safety mode:Preent large spike signal grneration when operationg emchanical-typeattenuator             Interference frdiator:<0.1&mu;V(at ouptput frequency),<1&mu;V(over entirefrequency range mmultl-menu display:OFF)             *At point 25mm from cabinet measured with 25 mm diameter loop antenna (2windings)terminated at 50&Omega;
Signal purity	Spurious(CW mode,&le;+7dBm)             HarmonicsL<-30dBc(2nd,3rd)             Non-harmonic:<-100dBc (&ge;15kHz offset)             Those related power:<-40dBc(<15kHz offset)             SSB phase noise(CW Mode,20kHz offset):             <-140dBc/Hz(10 to 256MHz),<-136dBc/Hz(256 to 512MHz),<130dBc/Hz(512to 1040MHz)             <-124dBc/Hz (>1040MHz,MG3642A only)             Residual AM:<-80 dBc (&ge;500kHz ,CW mode,+7dBm,50Hz to 15kHz demodulationband)             Residual FM(CW mode)             300Hz to 3 kHz demodulation band:<4Hzrms(10 to <512MHz),<8Hzrms(512to 1040MHz,MG3642A only)             50Hz to 15kHz demodulation band:<5Hzrms(10 to <512MHz),<8Hzrms(512to 1040MHz,MG3642A only)
Amplitude             modulation	Range:0% to 100%             Resolution:0.01%             Accuracy:±(5% of set value+2%)*&ge;0.4MHz ,&le;+7dBm,&le;90%AM,source:lnt 1(1kHz),300Hzto 3kHz demodulation band             Modulation frequency response(output:&le;±+7dBm)             Carrier frequency                                                  Upper limit frequency Lower limit frequency AM:30% AM:90% 0.4 to <0.5MHz 2kHz(±1dB bandwidth) 1kHz(±1dB bandwidth) DC External DC coupling(±1dB bandwidth)                         20Hz:External AC coupling(±1 dB bandwith) 0.5 to <2MHz 10kHz(±1dB bandwidth) 5kHz(±1dB bandwidth) 2 to <32MHz 20kHz(±1dB bandwidth) 32 to <64MHz 50kHz(±1dB bandwidth) &ge;64MHz 50kHz(±1dB bandwidth),100kHz(±1dB bandwidth)             Distortion:<-40dB (30% AM),<-30dB(90%AM)*&ge;0.4MHz,&le;+7dBm,source:lnt1(1kHz)             Incidental FM:<200 Hz peak*&ge;0.4MHz &le;+7dBm source:lint 1 (1kHz)300Hzto 3kHz demodulation band             Modulation signal source:One of internal (lint 1,lnt 2,lnt 3)and external(Ext 1, Ext 2)             Modulation signal Positive/negative switchable
Frequency             modulation	Range:             0 to 125Hz (125 to <250kHz) 0 to 25.6kHz(16 to <32MHz) 0 to 250Hz(250 to <500kHz) 0 to 51.2kHz(32 to <64MHz) 0 to 500Hz(0.5 to <1MHz) 0 to 102kHz(64 to <128MHz) 0 to 1kHz(1 to< 2MHz) 0 to 256kHz(128 to <256MHz) 0 to 2kHz (2 to< 4MHz) 0 to 512kHz(256 to 512MHz) 0 to 4kHz(4 to< 8MHz) 0 to 1024kHz(512 to 1040MHz) 0 to 10kHz(8 to <16MHz) 0 to 2048kHz(>1040MHz,MG3642A only)                          Resolution:             1Hz(0 to 4kHz deviation) 250 Hz(102.25 to 256kHz deviation) 10Hz(4.01 to 10kHz deviation) 500 Hz(256.5 to 512 kHz deviation) 25Hz(10.025 to 25.6kHz deviation) 1kHz (513 to 1024kHz deviation) 50Hz(25.65 to 51.2kHz deviation) 1kHz(1025 to 2048kHz deviation,NG3642A only) 100Hz(51.3 to 102kHz deviation)             Accuracy:±(5% of set value+10Hz)(0.4 to <512MHz),±(5% of set value+20Hz)(512to 1040MHz)             ±(5% of set value+40 Hz)(>1040MHz,MG3642A only)             *Source:lnt 1(1kHz),300 Hz to 3kHz demodulation band             Modulation frequency response:DC or 20 Hz*^3 to 20kHz(0.4 to <10MHz)DCor 20Hz*^3 to 100kHz(&ge;10MHz)*±1dB bandwidth             Distortion:<-40dB*&ge;16MHz,3.5kHz deviation,source:lnt 1(1kHz)             <-45dB*&ge;16MHz,3.5kHz deviation,source:lnt 1(1kHz)             Incidental FM:<1% peak*&ge;64MHz,&le;+7dBm,100kHz deviation,source:;lnt 1(1kHz),300Hzto 3kHz demodulation band             External modulation grop delay:<30&mu;s*&ge;10MHz,source:external DC couplingmodemmodulation rate:&le;100kHz             Modulation signal source(FM1,FM2):One of internal (lnt 1,lnt 2,lnt 3),andexternal (Ex 1 ,Ext 2)             Modulation signal polarity:FM 1, FM 2 positive/negative switchable
Pulse modulation	Accrding to option specifications
Modulation signal source	Internal modulation(lnt 1)             Frequency:400Hz ,1 kHz             Accuracy:Same as reference oscillator accuracy             Internal modulation (lnt 2,lnt 3):According to option specifications             External modulation(Ext 1,Ext 2)             Proper input level:2 Vp-p approx             Input impedance:600&Omega;,BNC connector             Coupling :DC/AC switchable
AF output	Output signal source:One of internal (lnt 1,lnt 2,lnt3),and external(Ext 1,Ext 2)             Output level:0 to 4Vp-p             Output level resolution:1m Vp-p             Output level accuracy:±(5% of setting level+2mVp-p)*Source:lnt 1 (1kHz)             Impedance:600&Omega;,BNC connector
Simultaneous             modulation	Excluking amplitued modulation and pulse modulation*^2combination,simultaneous modulation,modulation rate,edviation independently
Sweep function	Sweep parameters:Frequency,output level,memory             Sweep patterns             Frequency sweep(start/stop):Linear(specified step ieze and number of pointsf)Log(multiplyingfactor:1%)             Frequency sweep (center/span):Linear(specified step size and number of points)             Level sweep(start/stop,center/span):dB(specified step size and number ofpoints)* Sweep :continuous mode(max.20 dB width)             Memory mode:Auto ,single,manual             Sweep time             Setting range:1ms to 600s/point:0 V sweep end point:+10V),BNC connector(rearpanel)             Resolution:10 &mu;s)/point             Auxiliary output             X-Out:Ramp waveform(sweep start point:0 V,sweep end point:+10V),BNC connector(rearpanel)             Z-Out:TTL level(H-level at switching),BNC connector(rear panel)             Blanking-Out:TTL level(H-level at switching),BNC connector(rear panel)             Maker-Out:TTL level(H-level at switching),BNC connector(rear panel)
Functions	Relative display:Carrier frequency,output level             Offset display:Carrier frequency,output level             Memory:Saves/recalls 1000 panel settings,recall contents:panel,frequency,frequency/outputlevel selection             Trigger:An external trigger signal(rear panel BNC connector TTL level)canbe used to execute a previously programmed operation sequence (secept             power switch,preset key,local key and ratary knob operations),Max.numberof sequence steps of trigger program:20 steps             Back-up:The panel settings before power-off are back-upped and displayedagain at power-on,except data-input contents,GPIB data contents remote settings,RPPoperations             GPIB control:All functions,except power switch,local key,rotary knobs andresolutioh keys(Interface:SH1,AH1,T5,L3,TE0,SR1 RL1,PP0,DC1,DT1,             C0,E2)
Reverse power protection	Max.reverse input power:&le;50W(&le;1040MHz),&le;25W(>1040MHz,MG3642Aonly)±50Vdc
Power suply	*4Vac(+10%,-15%),47.5 to 63/380 to 420Hz &le;200VA
Temperature	Operating:0 °to 50℃ Storage:-30 °to +71℃
Dimensions and mass	320(W)*177(H)*451(D)mm,&le;20kg
EMC	EN55011:1991 ,Group 1, Class A             EN50082-1:1992             Harmonic current emissions:EN61000-3-2(1995)
Safety	EN61010-1:1993(Installation Category II ,Pollution DegreeII)

订货信息

Model /Order No.	Name
	Main frame
MG3641A	Synthesized Signal Generator
	Standard accessories
J0017F	Power cored ,2.5m:	1pc
B0325	GPIB connector shiedlded cap:	1pc
F0013	Fuse,5A (for 200Vac mains):	2pcs
F0012	Fuse,3.15 A (for 200Vac mains):	2pcs
W1137AE	MG3641A/3642A operation manual	1copy
W1137BE	MG3641A/3642A service manual:	1copy
	Options
MG3641[]A-01	Reference oscillator (aging rate:5*10^-10/day)
MG3641[]A-11	Pulse modulatior(pulse repetition rate:DCto 1 MHz )
MG3641[]A-21	AF synthesizer(0.01 Hz to 400kHz ,resolution:0.01Hz)
MG3641[]A-22	FSK encoder(2 or 4 levels FSK)
MG3641[]A-23	Pattern generator
	Application software
MX364001B*^1	Software foe Pattern Generator Data Write(Microsoft@ Windows 95)
	Optioonal accessories
J0576B	Coaxial cord(N-P·5D-2W·N-P),1m
J0127B	Coaxial cord(BNC-P·RG58A/U·BNC-P),1m
J0007	GPIB cable,1m,
J0008	GPIB cable,2m
MP51A	Pad
MP52A	Pad
MA1612A	Four-Point Juntion Pad
MP721[]	Atenuator(DC to 12.4GHz)
B0395C	Rack mount kit(EIA/IEC)
B0329G	Front cover(3/4MW 4U)
B0412A	Carrying case(with casters and B0329G frontcover)
B0330B	Tit bail (3/4MW 450D)