DIY编程器网

 找回密码
 注册

QQ登录

只需一步,快速开始

扫一扫,访问微社区

查看: 3389|回复: 1
打印 上一主题 下一主题

[资料] PIC16F7X PIC16F8X FLASH EEPROM 编程规范之电压要求

[复制链接]
跳转到指定楼层
楼主
发表于 2014-11-27 09:55:38 | 只看该作者 |只看大图 回帖奖励 |倒序浏览 |阅读模式
本帖最后由 shangdawei 于 2014-11-27 09:58 编辑

PIC16F7X
FLASH Memory Programming Specification
1.0 PROGRAMMING THE PIC16F7X
The PIC16F7X is programmed using a serial method.
The Serial mode allows the PIC16F7X to be programmed while in the users’ system, allowing for increased design flexibility.
This programming specification applies to PIC16F7X devices in all packages.
1.1 Hardware Requirements
The PIC16F7X requires two programmable power supplies, one for VDD (2.0V to 5.5V) and the other for VPP of 12.75V to 13.25V.
Both supplies should have a minimum resolution of 0.25V.
编程和擦除 高电平要求 4.75 * 0.8 = 3.8V
供电电压小于 4.75V 只能读取和验证


PIC16F8X
EEPROM Memory Programming Specification
1.0 PROGRAMMING THE PIC16F8X
The PIC16F8X devices are programmed using a serial method. The Serial mode will allow these devices to be programmed while in the user’s system.
This allows for increased design flexibility. This programming specification applies to only the above devices in all packages.
1.1 Hardware Requirements
The PIC16F8X devices require one programmable power supply for VDD (4.5V to 5.5V) and a VPP of 12V to 14V.
Both supplies should have a minimum resolution of 0.25V.
高电平最小要求 4.5 * 0.8 = 3.6V





分享到:  QQ好友和群QQ好友和群 QQ空间QQ空间 腾讯微博腾讯微博 腾讯朋友腾讯朋友 微信微信
收藏收藏 分享分享 支持支持 反对反对
沙发
发表于 2015-1-2 23:28:37 | 只看该作者
好资料,感谢分享
您需要登录后才可以回帖 登录 | 注册

本版积分规则

小黑屋|文字版|手机版|DIY编程器网 ( 桂ICP备14005565号-1 )

GMT+8, 2024-12-23 23:59 , 耗时 0.097736 秒, 20 个查询请求 , Gzip 开启.

各位嘉宾言论仅代表个人观点,非属DIY编程器网立场。

桂公网安备 45031202000115号

DIY编程器群(超员):41210778 DIY编程器

DIY编程器群1(满员):3044634 DIY编程器1

diy编程器群2:551025008 diy编程器群2

QQ:28000622;Email:libyoufer@sina.com

本站由桂林市临桂区技兴电子商务经营部独家赞助。旨在技术交流,请自觉遵守国家法律法规,一旦发现将做封号删号处理。

快速回复 返回顶部 返回列表